Laser Machine Best Choice Product provide laser cnc,laser engraving machine,laser machine,laser printer,laser wood machine Excellent Clearance Reci W6 130W CO2 Laser Tube Length 1650mm Dia. 80mm for CO2 Laser Engraving Cutting Machine. Get Discount Now! Only US $1092.50/piece at this time. Hurry buy Now before back to normal price! Normal price US $1150.00 or you can Check price now. Dont waste your time. Buy Now only in Shenzhen Qida Laser Tech Company Store Trusted Seller Store!
Terrific Discount Excellent Clearance Reci W6 130W CO2 Laser Tube Length 1650mm Dia. 80mm for CO2 Laser Engraving Cutting Machine item can enhance the quality of your life. Qualified to be purchased. Economical rate and also free delivery. Let's get Promo Excellent Clearance Reci W6 130W CO2 Laser Tube Length 1650mm Dia. 80mm for CO2 Laser Engraving Cutting Machine before prices rise.
Parameter：
Packaging：
Reci W6 130W CO2 Laser Tube Length 1650mm Dia. 80mm for CO2 Laser Engraving Cutting Machine
Mark & Model: W6, The product is featured as small size and good model, higher power rate compared with the laser tube of similar length and longer service time, which is suitable for laser marking, laser cutting and laser engraving.
1. Installation Requirement:
Make sure to follow the operation instruction of model W6 as shown in the illustration. The dedicated power P16 should be equipped. The positive pole of laser tube is in high voltage (the ignition voltage is 24kv). It may cause the following consequence when it is failed to follow the instruction: Arcing; the inner tube will be punctured by electricity and may cause water leakage.
2. Operation conditions:
Water cooling: using purified water; 3 to 5 liter/minute; water temperature: 10℃-40℃.
The operating environment: temperature 2-40℃; Humidity 10-60%.
The working current: test current is 32mA. Maximum working current is 32mA. The running current must be kept below 30mA. The life span can reach 10,000 hours if the current is kept below 28mA. The ammeter must be connected to the negative electrode of laser tube.
When it is working under over-high current for long term, the negative pole will appear Purple and the life span will be shortened rapidly.
To protect dust from going into the insulation sheath, please wrap it with plastic film.
3. Working Performance:
Cutting function.
Engraving function: Very good. When the working current is 4mA and the tube is in the state of preionization, the laser can be used for high-frequency impulse engraving.
4. Key Notes:
Do not clean the exterior surface of the output widow mirror with tools such as tampon; otherwise the output power will be seriously affected. The followings are the designated methods to clean up pollution in the exterior surface of window mirror:
1) When the mirror is polluted, do not turn on the laser.
2) Blow the mirror surface sideways with an air blower.
3) Spray the pure alcohol on the mirror surface with sprayer.
4) Turn on the laser after the alcohol gets fully volatilized.
5) If the methods above dont work effectively, it is necessary to ask for the professional to use tampon with alcohol to clean the mirror surface from middle to edge. The best solution is to prevent the window from being polluted.
Attention: it is forbidden to clean the mirror with acetone.
The screws in the front and back ends of the laser tube are not allowed to be moved, otherwise the output power will be declined, even the tube will be scrapped.
Put the acryl 300mm far away from output mirror, when testing its laser spot.
5. Safety:
The laser beam is invisible light. Please wear protective glasses when debugging the laser. The positive pole is in high voltage. Pay attention to the security marks.
6. Storage and Transportation Requirement:
Pour out cooling fluid in the event of storage and transportation, and cover the output terminal with a dust-proof plastic bag. The storage environment is 2-40℃, and the requested humidity is 10-60%. Pack the laser as in the original way.
Important notes: it is requested to use adhesive tape to cement the sponge together with laser tube to prevent the tube from vertically sliding during transportation. The sponge in the side of output mirror must be 70 mm beyond it, and the sponge in the side of reflecting mirror must be 50 mm wider.
7. Tubes operated in wrong way are not guaranteed by Manufacturer.
Return Policy
If the product you receive is not as described or low quality, the seller promises that you may return it before order completion (when you click "Confirm Order Received" or exceed confirmation timeframe) and receive a full refund. The return shipping fee will be paid by you. Or, you can choose to keep the product and agree the refund amount directly with the seller.N.B.: If the seller provides the "Longer Protection" service on this product, you may ask for refund up to 15 days after order completion.
Seller Service
On-time Delivery: If you do not receive your purchase within 60 days, you can ask for a full refund before order completion (when you click "Confirm Order Received" or exceed confirmation timeframe).Excellent Clearance Reci W6 130W CO2 Laser Tube Length 1650mm Dia. 80mm for CO2 Laser Engraving Cutting Machine
No comments:
Post a Comment