Sunday, August 5

Big Limited Original Leadshine driver 3ND583 laser machine parts cnc router Fitting cnc router machine parts

Big Limited Original Leadshine driver 3ND583 laser machine parts cnc router Fitting cnc router machine parts Rating: 5 out of 5

Laser Machine Best Choice Product provide laser cnc,laser engraving machine,laser machine,laser printer,laser wood machine Big Limited Original Leadshine driver 3ND583 laser machine parts cnc router Fitting cnc router machine parts. Get Discount Now! Only US $49.50/piece at this time. Hurry buy Now before back to normal price! Normal price US $55.00 or you can Check price now. Dont waste your time. Buy Now only in Kind&Kinds Store Trusted Seller Store!
His service is very best and faster. Buy Special Big Limited Original Leadshine driver 3ND583 laser machine parts cnc router Fitting cnc router machine parts today, Shop Admin sent today too. If buying in bulk then there is a special price . This Big Limited Original Leadshine driver 3ND583 laser machine parts cnc router Fitting cnc router machine parts item is highly recommended for you.

Affordable rate and totally free delivery. Let's acquire prior to rates increase.

No question, this is a genuine item that gives several benefits in addition to successful for you. Equally as you will obtain a fortune, this Flash Deal Big Limited Original Leadshine driver 3ND583 laser machine parts cnc router Fitting cnc router machine parts product has the ability to supply a lorry that must be really intriguing for you. In selecting this Clearance Big Limited Original Leadshine driver 3ND583 laser machine parts cnc router Fitting cnc router machine parts product, you can do numerous factors to consider that are provided in the directory. The goods catalog you get is definitely provide a recommendation for those of you that wish to locate the product you want.

Leadshine 3ND583 3-phase microstepping Drive work 36-50 VDC out 2.1A to 8.3A for Associated products NEMA 23 stepper motor

Typical Connection

Mechanical Specifications (unit: mm [inch])

2 Connector Configuration :

Connector P1 Configurations

Pin Function

Details

PUL+

Pulse signal: In single pulse (pulse/direction) mode, this input represents pulse signal, each rising or falling edge active (software configurable); 4-5V when PUL-HIGH, 0-0.5V when PUL-LOW. In double pulse mode (pulse/pulse) , this input represents clockwise (CW) pulse,active both at high level and low level (software configurable). For reliable response, pulse width should be longer than 2.5µs. Series connect resistors for current-limiting when +12V or +24V used. The same as DIR and ENA signals.

PUL-

DIR+

DIR signal: In single-pulse mode, this signal has low/high voltage levels, representing two directions of motor rotation; in double-pulse mode (software configurable), this signal is counter-clock (CCW) pulse,active both at high level and low level (software configurable). For reliable motion response, DIR signal should be ahead of PUL signal by 5µs at least. 4-5V when DIR-HIGH, 0-0.5V when DIR-LOW. Please note that rotation direction is also related to motor-drive wiring match. Exchanging the connection of two wires for a coil to the drive will reverse motion direction.

DIR-

ENA+

Enable signal: This signal is used for enabling/disabling the drive. High level (NPN control signal, PNP and Differential control signals are on the contrary, namely Low level for enabling.) for enabling the drive and low level for disabling the drive. Usually left UNCONNECTED (ENABLED).

ENA-

Connector P2 Configurations

Pin Function

Details

+Vdc

Power supply, 20~50 VDC, Including voltage fluctuation and EMF voltage.

GND

Power Ground.

A+, A-

Motor Phase A

B+, B-

Motor Phase B

3 Microstep&Current :

Microstep Resolution Selection

When its not in software configured mode, microstep resolution is set by SW5, 6, 7, 8 of the DIP switch as shown in the following table:

Microstep

Steps/rev.(for 1.8o motor)

SW5

SW6

SW7

SW8

1 to 512

Default/Software configured

on

on

on

on

2

400

off

on

on

on

4

800

on

off

on

on

8

1600

off

off

on

on

16

3200

on

on

off

on

32

6400

off

on

off

on

64

12800

on

off

off

on

128

25600

off

off

off

on

5

1000

on

on

on

off

10

2000

off

on

on

off

20

4000

on

off

on

off

25

5000

off

off

on

off

40

8000

on

on

off

off

50

10000

off

on

off

off

100

20000

on

off

off

off

125

25000

off

off

off

off

Mechanical Specifications (unit: mm [inch]) :

Return Policy

If the product you receive is not as described or low quality, the seller promises that you may return it before order completion (when you click "Confirm Order Received" or exceed confirmation timeframe) and receive a full refund. The return shipping fee will be paid by you. Or, you can choose to keep the product and agree the refund amount directly with the seller.
N.B.: If the seller provides the "Longer Protection" service on this product, you may ask for refund up to 15 days after order completion.

Seller Service

On-time Delivery: If you do not receive your purchase within 60 days, you can ask for a full refund before order completion (when you click "Confirm Order Received" or exceed confirmation timeframe).
Big Limited Original Leadshine driver 3ND583 laser machine parts cnc router Fitting cnc router machine parts

No comments:

Post a Comment

Popular Posts